名片曝光使用說明

步驟1:創建名片

微信掃描名片二維碼,進入虎易名片小程序,使用微信授權登錄并創建您的名片。

步驟2:投放名片

創建名片成功后,將投放名片至該產品“同類優質商家”欄目下,即開啟名片曝光服務,服務費用為:1虎幣/天。(虎幣充值比率:1虎幣=1.00人民幣)

關于曝光服務

名片曝光只限于使用免費模板的企業產品詳細頁下,因此當企業使用收費模板時,曝光服務將自動失效,并停止扣除服務費。

<

返回首頁

XQ-1(2B) 金相式樣鑲嵌機 Metallographic Specimen Mounting Press 用途 XQ-2B型金相試樣鑲嵌機(以下簡稱鑲嵌機)適用于對不是整形、不易手拿的微笑金相式樣進行熱固性塑料壓制。成形后可方便地進行試樣磨拋操作,也有利于在金相顯微鏡下進行縣委組織測定。 鑲嵌機在下列條件下能地工作。 1. 海拔高度不超過1000米; 2. 周圍介質溫度不高于 40℃,及不低于-10℃; 3. 空氣在相對濕度不大于85%(在20℃時); 4. 周圍沒有導電塵埃,爆炸性氣體,及能嚴重破壞金屬和絕緣的腐蝕性氣體; 5. 沒有明顯的震動和顛簸。 Applications Model XQ-2B Metallographic Specimen Mounting Press(mounting press for shortp) is applicable for the most plastics pressing forming of tiny fractonal metallographic specimen. After formed, the specimen can be grinded and polished easily and its microstructure can be measured readily under metalloscope. The reliability of the mounting press can be assured under following conditions: 1. Altitude above the sea level less than 1000m. 2. Ambient temperature between 40 and -10. 3. Air relative humidity less than 85%(at 20 ). 4. No conductive dust, explosive gas and corrosive gas harmful to metal and insulation are insulation are around the machine. 5. No apparent Vibration and shaking. 結構特征概述 本機系機械式鑲嵌機,旋轉機休外手輪,通過一對錐齒輪帶動機體內絲桿使壓制試樣的下模在鋼模套內上下移動,熱固性塑料連同鑲嵌的試樣在加熱的條件下成形。試樣制備過程中的成形壓力由成形壓力在機體內的彈簧自動補償,試樣壓制的壓力可由信號燈給以指示。 本機配有智能型數字顯示溫控器,能自動控溫,設定溫度與實測溫度均有顯示,溫度傳感器采用熱電偶。本機具有高靈敏度、高精度,有溫度顯示,易觀察又易操作等優點。每件試樣鑲嵌(用電玉粉)約12分鐘。 Brief Description The mounting press is a mechanical type machine. By turning the hand-wheel outside the machine, a couple of bevel gear is rotated to drive the screw rod which in turn pushes/pulls the lower dieup and down along the mould sleeve, the thermosat plastics together with specimen being mounted is formed under heated conditions. During this process the pressure is self adjusted by a spring fixed inside the machine. A signal light is used to indicate the pressure level. 技術參數 1.試樣壓制規格 Specimen pressing size Φ22x15mm Φ30x15mm Φ45x15mm 2.加熱器規格 Heater capacity 650w,220v 800w,220v 3.溫度調節范圍 Adjustable temperature range 0~160℃ 4.控制電源 Power 電壓波動不大于±15 0v.50hz, voltage fluctuation less than ±15% 5.外形尺寸 Overall dimensions 340x280x400mm 6.凈重 Net Weight 32kg
產品推薦
“廠家直供XQ-1金相試樣鑲嵌機”信息由發布人自行提供,其真實性、合法性由發布人負責。交易匯款需謹慎,請注意調查核實。
主站蜘蛛池模板: 洞头县| 德庆县| 河东区| 桂平市| 嘉义县| 孙吴县| 璧山县| 右玉县| 平阴县| 东阿县| 宜宾市| 夏邑县| 沅陵县| 芜湖市| 九江市| 明水县| 铜陵市| 视频| 临邑县| 凤冈县| 宜城市| 平昌县| 华池县| 克拉玛依市| 西乡县| 法库县| 会东县| 科尔| 旬阳县| 宜春市| 仁化县| 江都市| 翁牛特旗| 奉化市| 嵊州市| 密山市| 涿州市| 项城市| 景洪市| 上蔡县| 京山县|