產品分類 更多>>
產品推薦
廠家(產地)
沙伯基礎(原GE)
牌號
144R-111
特性級別
透明級
用途級別
食品級
銷售方式
品牌經銷
類型
標準料
| Physical | Nominal Value | Unit | Test Method |
Specific Gravity | ASTM D792 | ||
-- | 1.20 | ||
-- | 1.19 | g/cm3 | |
Specific Volume | 23.0 | in3/lb | ASTM D792 |
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg) | 11 | g/10 min | ASTM D1238 |
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg) | 0.610 | in3/10min | ISO 1133 |
Molding Shrinkage - Flow (0.126 in) | 5.0E-3 to 7.0E-3 | in/in | Internal Method |
Water Absorption | ASTM D570 | ||
24 hr | 0.15 | % | |
Equilibrium, 73°F | 0.35 | % | |
Equilibrium, 212°F | 0.58 | % | |
| Hardness | Nominal Value | Unit | Test Method |
Rockwell Hardness | ASTM D785 | ||
M-Scale | 70 | ||
R-Scale | 118 |
| Mechanical | Nominal Value | Unit | Test Method |
Tensile Modulus | |||
-- 3 | 344000 | psi | ASTM D638 |
-- | 341000 | psi | ISO 527-2/1 |
Tensile Strength | |||
Yield 4 | 8990 | psi | ASTM D638 |
Yield | 9140 | psi | ISO 527-2/50 |
Break 4 | 9860 | psi | ASTM D638 |
Break | 10200 | psi | ISO 527-2/50 |
Tensile Elongation | |||
Yield 4 | 7.0 | % | ASTM D638 |
Yield | 6.0 | % | ISO 527-2/50 |
Break 4 | 130 | % | ASTM D638 |
Break | 110 | % | ISO 527-2/50 |
Flexural Modulus | |||
1.97 in Span 5 | 339000 | psi | ASTM D790 |
-- 6 | 334000 | psi | ISO 178 |
Flexural Stress | |||
-- 6, 7 | 13100 | psi | ISO 178 |
Yield, 1.97 in Span 5 | 14100 | psi | ASTM D790 |
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel) | 10.0 | mg | ASTM D1044 |
| Impact | Nominal Value | Unit | Test Method |
Charpy Notched Impact Strength (73°F) | 17 | ft·lb/in2 | ISO 179/2C |
Notched Izod Impact | |||
Colors | 15 | ft·lb/in | ASTM D256 |
Natural, Tints | 15 | ft·lb/in | ASTM D256 |
73°F | 15 | ft·lb/in | ASTM D256 |
-22°F 8 | 4.8 | ft·lb/in2 | ISO 180/1A |
73°F 8 | 5.7 | ft·lb/in2 | ISO 180/1A |
Unnotched Izod Impact (73°F) | 60 | ft·lb/in | ASTM D4812 |
Instrumented Dart Impact (73°F, Energy at Peak Load) | 558 | in·lb | ASTM D3763 |
Gardner Impact (73°F) | 1500 | in·lb | ASTM D3029 |
Tensile Impact Strength 9 | 275 | ft·lb/in2 | ASTM D1822 |
| Thermal | Nominal Value | Unit | Test Method |
Deflection Temperature Under Load | |||
66 psi, Unannealed, 0.252 in | 279 | °F | ASTM D648 |
66 psi, Unannealed, 3.94 in Span 10 | 277 | °F | ISO 75-2/Be |
264 psi, Unannealed, 0.252 in | 270 | °F | ASTM D648 |
264 psi, Unannealed, 3.94 in Span 10 | 257 | °F | ISO 75-2/Ae |
Vicat Softening Temperature | |||
-- | 309 | °F | ASTM D1525 11 |
-- | 307 | °F | ISO 306/A50 |
-- | 286 | °F | ISO 306/B50 |
-- | 288 | °F | ISO 306/B120 |
Ball Pressure Test (257°F) | Pass | IEC 60695-10-2 | |
CLTE - Flow | |||
-40 to 203°F | 3.8E-5 | in/in/°F | ASTM E831 |
73 to 176°F | 3.9E-5 | in/in/°F | ISO 11359-2 |
Specific Heat | 0.299 | Btu/lb/°F | ASTM C351 |
Thermal Conductivity | |||
-- | 1.3 | Btu·in/hr/ft2/°F | ASTM C177 |
-- | 1.4 | Btu·in/hr/ft2/°F | ISO 8302 |
RTI Elec | 266 | °F | UL 746 |
RTI Imp | 266 | °F | UL 746 |
RTI Str | 266 | °F | UL 746 |
| Electrical | Nominal Value | Unit | Test Method |
Surface Resistivity | > 1.0E+15 | ohm | IEC 60093 |
Volume Resistivity | |||
-- | > 1.0E+17 | ohm·cm | ASTM D257 |
-- | > 1.0E+15 | ohm·cm | IEC 60093 |
Dielectric Strength | |||
0.126 in, in Air | 380 | V/mil | ASTM D149 |
0.126 in, in Oil | 430 | V/mil | IEC 60243-1 |
Dielectric Constant | |||
50 Hz | 3.17 | ASTM D150 | |
60 Hz | 3.17 | ASTM D150 | |
1 MHz | 2.96 | ASTM D150 | |
50 Hz | 2.70 | IEC 60250 | |
60 Hz | 2.70 | IEC 60250 | |
1 MHz | 2.70 | IEC 60250 | |
Dissipation Factor | |||
50 Hz | 9.0E-4 | ASTM D150 | |
60 Hz | 9.0E-4 | ASTM D150 | |
1 MHz | 0.010 | ASTM D150, IEC 60250 | |
50 Hz | 1.0E-3 | IEC 60250 | |
60 Hz | 1.0E-3 | IEC 60250 | |
Comparative Tracking Index (CTI) | PLC 2 | UL 746 | |
High Amp Arc Ignition (HAI) | PLC 1 | UL 746 | |
High Voltage Arc Tracking Rate (HVTR) | PLC 2 | UL 746 | |
Hot-wire Ignition (HWI) | PLC 2 | UL 746 | |
| Flammability | Nominal Value | Unit | Test Method |
Flame Rating (0.0579 in) | HB | UL 94 | |
Oxygen Index | 25 | % | ASTM D2863, ISO 4589-2 |
| Optical | Nominal Value | Unit | Test Method |
Refractive Index | 1.586 | ASTM D542 | |
Transmittance (100 mil) | 88.0 | % | ASTM D1003 |
Haze (100 mil) | 1.0 | % | ASTM D1003 |
| Injection | Nominal Value | Unit | |
Drying Temperature | 250 | °F | |
Drying Time | 3.0 to 4.0 | hr | |
Drying Time, Maximum | 48 | hr | |
Suggested Max Moisture | 0.020 | % | |
Suggested Shot Size | 40 to 60 | % | |
Rear Temperature | 520 to 560 | °F | |
Middle Temperature | 540 to 580 | °F | |
Front Temperature | 560 to 600 | °F | |
Nozzle Temperature | 550 to 590 | °F | |
Processing (Melt) Temp | 560 to 600 | °F | |
Mold Temperature | 160 to 200 | °F | |
Back Pressure | 50.0 to 100 | psi | |
Screw Speed | 40 to 70 | rpm | |
Vent Depth | 1.0E-3 to 3.0E-3 | in |
本公司長期代理銷售沙伯基礎、奇美、帝人、出光等PC塑料多種牌號產品
我司產品均可提供物性表(英文和中文版)、加工參數表、ROHS(SGS)、物質安全表MSDS、UL黃卡及FDA認證等相關資料；免費為客戶分析樣版并提供原料型號咨詢服務(可免費幫客戶翻譯英文資料)；如需試料、了解產品相關信息及當日報價，敬請來電、來郵及在線咨詢，竭誠為您服務！
由于市場行情有波動，詳細價格請旺旺或者來電咨詢，為此造成的不便，請您諒解。
手機/微信：18025166516 電話：0769-33303936
QQ：1106575696 郵箱：1106575696@qq.com
