產品分類 更多>>
1.生產概要
1-1 Specification 規格
Input Voltage 輸入電壓 220V AC
Power Consumption 耗電量 600W
Air pump 空氣泵 diaphragm pump 膜片式專用泵
Capacity 流量 24L/min (max)
Hot Air Temperature 熱風溫度 100-480℃
Weight 重量 3.3 KG
Dimensions 外形尺寸 246mm(L) * 187mm(W) * 127mm(H)
1-2 Function產品特性
*Prevent static electric and creepage to damage the PCB.
防靜電設計，防止靜電和漏電損壞PCB板。
*Unnecessary touch the PCB, so can avoid moving element and heating impaction.
出風口不必接觸PCB板，這樣可以避免移動元件，和堵塞出風口。
*Extensively adjust air and temperature and select different nozzle,so it can fit most of SMD.
廣泛地調節風量和溫度，選擇不同的風嘴，這樣可以適合大多數貼片。
*Use inlet heating element,the type of heating element and nozzle is same as the international.
采用加熱元件，風嘴的類型是國際上通用的。
*Delay to blow air when turn the power switch off,if can protect the automatic.
當關閉電源開關，風量會延遲關閉。輸送冷風避免發熱芯損壞。
1-3 Usefulness用途
*Fits most of SMD.Such as SOIC,CHIP,QFP,PLCC,BGA etc.
適合大多數貼片，比如SOIC,CHIP,QFP,PLCC,BGA等封裝形式。
*Contract hose.
收縮熱縮管。
Operating Instructions操作說明
2-1 Before Operation 操作前
*Select the FP Pick-up wire that matches the size the IC.
選擇與集成電路塊的尺寸大小相匹配的起拔器（注：起拔器需另行購買）。
The Fp Pick-up has an S wire(14mm)attached to it,but an L wire(30mm)may be necessary,depending on the size of the IC.Choose the appropriate wire for the IC.
選擇與集成電路尺寸相配合的起拔鋼絲。FP起拔器配有小鋼絲（14毫米），但可能需要大起拔鋼絲（30毫米）。請依照集成電路塊尺寸，選擇適當的起拔鋼絲。
*Select the Nozzle that matches the size of the IC.
選擇與集成電路塊尺寸相匹配的風嘴。
Attach the Nozzle when both the Pipe and Nozzle are cool.
當管道和風嘴都冷卻時再更換風嘴。
*Loosen the screw on the Nozzle.
擰開風嘴的螺絲。
*Attach the Nozzle.
裝置風嘴。
*Retighteen the screw properly.
適當地擰緊螺絲。
2-2 QFP Desoldering QFP脫焊
*Plug the power cord into the power supply.
將電源線插入電源供應器。
After connection,the automatic blowing function will start sending air through the pipe,but the Heating Element remains cool.
連接后，自動送風功能將開始通過管道輸送空氣，但是加熱元件保持冷卻。
*Turn the power switch on.打開電源開關。
The Power Switch may be turued on at any time while the automatic blowing function,is operating.Once the Power Switch is turned on,the Heating Element will begin to warm up.
當自動送風功能運行的時候，電源開關可隨時打開。當電源開關開啟時，加熱元件開始升溫。
*Adjust the Air Flow and Temperature Control Knobs.
調節風量和溫度控制按鈕。
After adjusting the Air Flow and Temperature Control Knob, wait for the temperature to stabilize for a short period of time.We recommend you to adjust the temperature around 300 to 350 ℃.As for Air flow in case of single nozzle,set the knob 1-5,in another nozzle,set it from 4-8.When using a single nozzle,set the Temperature Control Knob to higher than 6.
調節風量和溫度控制按鈕之后，稍等一會兒，待溫度穩定下來。我們建議您將溫度調整到300-350℃左右。至于風量，在單個風嘴的情況下，可以設置在1-5檔，另外一個風嘴，可以設置在4-8,。當使用單個風嘴的時候，溫度控制按鈕設置要高于6.
*Place the FP Pick – up under IC lead.
